|
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_check_connection (UINT16 handle, BD_ADDR bd_addr, UINT16 *p_lcid) |
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_control (uint16_t handle, uint8_t signal) |
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_create_connection (uint16_t uuid, uint8_t scn, wiced_bool_t is_server, uint16_t mtu, wiced_bt_device_address_t bd_addr, uint16_t *p_handle, wiced_bt_port_mgmt_cback_t *p_mgmt_cb) |
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_flow_control (uint16_t handle, wiced_bool_t enable) |
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_remove_connection (uint16_t handle, wiced_bool_t remove_server) |
| |
| wiced_bt_dev_status_t | wiced_bt_rfcomm_set_buffer_pool (uint16_t buffer_size, uint16_t buffer_count) |
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_set_data_callback (uint16_t port_handle, wiced_bt_rfcomm_data_cback_t *p_cb) |
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_set_event_callback (uint16_t port_handle, wiced_bt_port_event_cback_t *p_port_cb) |
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_set_event_mask (uint16_t port_handle, wiced_bt_rfcomm_port_event_t mask) |
| |
| wiced_bt_rfcomm_result_t | wiced_bt_rfcomm_write_data (uint16_t handle, char *p_data, uint16_t max_len, uint16_t *p_len) |
| |
The RFCOMM protocol provides emulation of serial ports over the L2CAP protocol. The protocol is based on the ETSI standard GSM 7.1.0. RFCOMM is a simple transport protocol, with additional provisions for emulating the nine circuits of RS-232 (ITU-T V.24) serial ports. The RFCOMM protocol supports up to 60 simultaneous connections between two Bluetooth devices. The number of connections that may be used simultaneously in a Bluetooth device is implementation-specific.
This function checks connection referenced by handle is up and running.
- Parameters
-
- Returns
- WICED_BT_RFCOMM_SUCCESS : If successful WICED_BT_RFCOMM_LINE_ERR : If connection is not up and running
Send control signal to the peer device.
- Parameters
-
- Returns
- WICED_BT_RFCOMM_SUCCESS : If successful WICED_BT_RFCOMM_BAD_HANDLE : If the handle is out of range WICED_BT_RFCOMM_NOT_OPENED : If the connection is not opened
Establish serial port connection to the peer device, or allow RFCOMM to accept a connection from peer devices.
- Note
- Server can call this function with the same scn parameter multiple times if it is ready to accept multiple simulteneous connections.
DLCI for the connection is (scn * 2 + 1) if client originates connection on existing none initiator multiplexer channel. Otherwise it is (scn * 2). For the server DLCI can be changed later if client will be calling it using (scn * 2 + 1) dlci.
- Parameters
-
| [in] | uuid | : The Universal Unique Identifier (UUID) of the Class ID of the service being opened |
| [in] | scn | : The Service Channel Number(SCN) as registered with the SDP (server) or obtained using SDP from the peer device (client) |
| [in] | is_server | : TRUE if requesting application is a server |
| [in] | mtu | : The maximum number of bytes transferred per frame If 0, a default size of L2CAP_MTU_SIZE minus 5 bytes is used |
| [in] | bd_addr | : BD_ADDR of the peer (if client), NULL if server |
| [in] | p_mgmt_cb | : Pointer to callback function to receive connection up/down events |
| [out] | p_handle | : A pointer to the handle set by RFCOMM to be used in consecutive calls for this connection |
- Returns
- WICED_BT_RFCOMM_SUCCESS : If successful WICED_BT_RFCOMM_ALREADY_OPENED : If the client tries to establish a connection to the same BD_ADDR WICED_BT_RFCOMM_NO_RESOURCES : If there is not enough memory to allocate a control block structure
This function directs a specified connection to pass flow control message to the peer device. Enable flag passed shows if port can accept more data.
- Parameters
-
- Returns
- WICED_BT_RFCOMM_SUCCESS : If successful WICED_BT_RFCOMM_BAD_HANDLE : If the handle is out of range WICED_BT_RFCOMM_NOT_OPENED : If the connection is not opened
Close the specified connection.
- Parameters
-
| [in] | handle | : The connection handle returned by wiced_bt_rfcomm_create_connection . |
| [in] | remove_server | : (for server only) If TRUE, then also remove server; otherwise server remains enabled after connection is closed. |
- Returns
- WICED_BT_RFCOMM_SUCCESS : If successful WICED_BT_RFCOMM_BAD_HANDLE : If the handle is out of range WICED_BT_RFCOMM_NOT_OPENED : If the connection is not opened
Function wiced_bt_rfcomm_set_buffer_pool
If buffer_size > 0 and wiced_bt_rfcomm does not have a private pool yet,
this function allocates a private buffer pool.
If buffer_size = 0 and wiced_bt_rfcomm has a private buffer pool,
this function deallocates the private buffer pool.
- Parameters
-
| [in] | buffer_size | : data size for the private pool. The actual buffer size includes additional overhead. |
| [in] | buffer_count | : number of buffers in this new pool. |
- Returns
- WICED_BT_SUCCESS if the action was carried out successfully as desired WICED_BT_NO_RESOURCES no resources.
Set event data callback the specified connection.
- Parameters
-
| [in] | port_handle | : A 16-bit unsigned integer returned by wiced_bt_rfcomm_create_connection |
| [in] | p_cb | : Address of the callback function which should be called from the RFCOMM when a data packet is received |
- Returns
- WICED_BT_RFCOMM_SUCCESS : If successful WICED_BT_RFCOMM_BAD_HANDLE : If the handle is out of range WICED_BT_RFCOMM_NOT_OPENED : If the connection is not opened
Set event callback the specified connection.
- Parameters
-
| [in] | port_handle | : A 16-bit unsigned integer returned by wiced_bt_rfcomm_create_connection |
| [in] | p_port_cb | : Address of the callback function which should be called from the RFCOMM when an event specified in the mask occurs |
- Returns
- WICED_BT_RFCOMM_SUCCESS : If successful WICED_BT_RFCOMM_BAD_HANDLE : If the handle is out of range WICED_BT_RFCOMM_NOT_OPENED : If the connection is not opened
Set events for which to be notified
- Parameters
-
- Returns
- WICED_BT_RFCOMM_SUCCESS : If successful WICED_BT_RFCOMM_BAD_HANDLE : If the handle is out of range WICED_BT_RFCOMM_NOT_OPENED : If the connection is not opened
| wiced_bt_rfcomm_result_t wiced_bt_rfcomm_write_data |
( |
uint16_t |
handle, |
|
|
char * |
p_data, |
|
|
uint16_t |
max_len, |
|
|
uint16_t * |
p_len |
|
) |
| |
This function sends the given application data to the peer device. If wiced_bt_rfcomm_set_buffer_pool() was called to create a private buffer pool, the buffer from the private buffer pool is used to hold the data in the RFCOMM TX queue. Otherwise, RFCOMM uses the RFCOMM_DATA_POOL_ID pool to hold the data.
- Parameters
-
- Returns
- WICED_BT_RFCOMM_SUCCESS : If successful WICED_BT_RFCOMM_BAD_HANDLE : If the handle is out of range WICED_BT_RFCOMM_NOT_OPENED : If the connection is not opened
